Dear Joseph Lee,
Thank you for your response. I will confirm the spec sheet from the manufacture for sensor position in this FP.
Best,
Search found 9 matches
- Thu Mar 26, 2020 3:01 pm
- Forum: Motive
- Topic: Question about AMTI properties
- Replies: 2
- Views: 2184
- Sat Mar 07, 2020 7:54 pm
- Forum: Motive
- Topic: Question about AMTI properties
- Replies: 2
- Views: 2184
Question about AMTI properties
Hi all, Q1 Let me know the meaning of the following AMTI properties displayed in the property pane and the exported CSV header. Electrical offset Plate length. Plate width. Q2 Does Motive automatically get these properties from AMTI configuration software? Q3 Do these above properties affect the pos...
- Wed Sep 13, 2017 5:32 am
- Forum: Motive
- Topic: Possible to recover deleted .tak files from Data pane ?
- Replies: 1
- Views: 2074
Possible to recover deleted .tak files from Data pane ?
Hi Due to my mistake, all the takes listed in Data pane were deleted with pushing delete button. In this case, there are no alert window shown before erasing tak list. Do anyone know whether my .tak files are stored elsewhere in my PC or completely erased from harddisk? Thanks in advance. Motive 2.0...
- Wed Nov 18, 2015 4:30 am
- Forum: Motive
- Topic: Force vector from AMTI not shown on M1.9b
- Replies: 1
- Views: 5414
Force vector from AMTI not shown on M1.9b
Hi, friends I'm testing the AMTI forceplate on the latest version of Motive 1.9 beta. My forceplate is AMTI BP600400 connected to PC through Gen 5 signal conditioner. There are two problems regarding the use of forceplate on Motive 1.9 beta. 1) Force vector always disappears after "set position...
- Thu Sep 03, 2015 4:10 am
- Forum: Motive
- Topic: .tak file cannot open. Any solution?
- Replies: 1
- Views: 5879
.tak file cannot open. Any solution?
Hi all, When I drag & drop one of .tak file, Motive showed an alert as the attached figure illustrates. Another .tak file in the same project can open without any problem. Does anyone has good solutions for this kind of problem? Would naturalpoint investigate what happen to my .tak file? This .t...
- Mon Sep 08, 2014 4:38 pm
- Forum: Motive
- Topic: CSV error during exporting multiple trials, Motive 1.6 beta
- Replies: 3
- Views: 3035
Re: CSV error during exporting multiple trials, Motive 1.6 b
Hi Dustin, I always appreciate your wok on this forum. Thank you for relying my question. The errors occur in trials from the same session. I did not select trials from more than two sessions. Is your environment Motive 1.6 beta 2? Another possible cause of this problem is, my video card. When I gra...
- Fri Sep 05, 2014 6:14 pm
- Forum: Motive
- Topic: CSV error during exporting multiple trials, Motive 1.6 beta
- Replies: 3
- Views: 3035
CSV error during exporting multiple trials, Motive 1.6 beta
Hi, friends When I want to export multiple trials in .CSV format, the same error always occurs. The procedure is, selecting multiple trials on the project pane [shift + mouse left clicking], and then, mouse right click -> export tracking data. This seemed to successfully export only current trial bu...
- Fri Jan 10, 2014 12:53 am
- Forum: Motive
- Topic: Manual labeling failed
- Replies: 7
- Views: 5452
Manual labeling failed
Hi, Since I upgraded Motive from 1.5 beta 2 to 1.5 final, the manual labeling always fails. After trajectorized 2d data with marker asset and label by right-clicking a unlabeled marker, the marker disappers. In this procedure, the Motive 1.5 beta 2 works correctly. Dose anyone have the same problem?...
- Fri Nov 15, 2013 4:58 am
- Forum: General OptiTrack Support
- Topic: Is the eSync output exactly the same as OptiTrack recording?
- Replies: 2
- Views: 2514
Is the eSync output exactly the same as OptiTrack recording?
Hi, I'd like to know how is the latency of eSync. Is it constact? or varies depending on the situation? To synchronize Optitrack with a forceplate, I record eSync output and forceplate signal using a data acquisition device. I wonder the OptiTrack recording starts 20 earlier than the eSync output si...