Search found 720 matches
- Mon Nov 30, 2015 10:55 am
- Forum: Motive
- Topic: There is a problem with the Auto Characterize.
- Replies: 3
- Views: 153584
Re: There is a problem with the Auto Characterize.
Hello Changwon, Positive z.jpg seems to be facing positive Z correctly. Could you please describe the problem you are having? You mention that with both poses you are experiencing a problem in charaterization, but if you could actually describe the problem it will help me to understand what is wrong...
- Fri Nov 27, 2015 3:15 pm
- Forum: General OptiTrack Support
- Topic: I can't do the characteriz.
- Replies: 1
- Views: 2035
Re: I can't do the characteriz.
Hello Changwon, Could you please describe the problem you are having with the auto characterize? I did notice that, if you select the character nodes that are created and open the Definition tab, the skeleton has been mapped but the Characterize check box has not been enabled. If you have the perfor...
- Fri Nov 27, 2015 3:15 pm
- Forum: Motive
- Topic: There is a problem with the Auto Characterize.
- Replies: 3
- Views: 153584
Re: There is a problem with the Auto Characterize.
Hello Changwon, Could you please describe the problem you are having with the auto characterize? I did notice that, if you select the character nodes that are created and open the Definition tab, the skeleton has been mapped but the Characterize check box has not been enabled. If you have the perfor...
- Wed Nov 25, 2015 10:30 am
- Forum: ARENA & Expression
- Topic: how to obtain joint angle from BVH ARENA/
- Replies: 4
- Views: 13342
Re: how to obtain joint angle from BVH ARENA/
Hello Maryam Alzawahreh, Thank you for reaching out to us regarding your questions. Our BVH should be pretty standard to the BVH format. There is a HIERARCHY section that describes the skeleton hierarchy, and MOTION section that describes the XYZ position of the root joint(hip) and rotation angles o...
- Mon Nov 23, 2015 3:10 pm
- Forum: OptiTrack Data Streaming
- Topic: Problem with the Matlab Sample and Data Streaming
- Replies: 4
- Views: 8106
Re: Problem with the Matlab Sample and Data Streaming
Hello Ali, Thank you for this. At a glance, I cannot see anything wrong with the code. Have you tried unicast, by chance? Since the issue seems to only occur when connecting from a remote machine, there may be some networking issue involved. You might try running one of the sample applications that ...
- Mon Nov 23, 2015 12:19 pm
- Forum: Camera SDK
- Topic: CameraSDK 2D data and UDP
- Replies: 4
- Views: 13178
Re: CameraSDK 2D data and UDP
Hello lnsundh, Thank you for reaching out to us regarding your question. The NatNet SDK is used to connect to the realtime data stream that is broadcast by our Motive software. If you are working with a single camera, you are most likely working with the Camera SDK, which will not provide the same h...
- Thu Nov 19, 2015 4:06 pm
- Forum: Motive
- Topic: Force vector from AMTI not shown on M1.9b
- Replies: 1
- Views: 5414
Re: Force vector from AMTI not shown on M1.9b
Hello ogasawara, Thank you for using OptiTrack, and thank you for reaching out to us regarding your issues. 1) We have not seen a problem where data is working before you "set position" and stops working after. We have, however, seen issues when the force plates are improperly set up that ...
- Thu Nov 19, 2015 2:49 pm
- Forum: Motive
- Topic: Obtain the evolution graph angles
- Replies: 1
- Views: 5311
Re: Obtain the evolution graph angles
Hello Grégoire, Thank you for reaching out to us. Motive does not have a graphic representation for joint angles at this time. The graph inside of Motive is only capable of showing Marker coordinates. In order to generate the graphs you are looking for, you may need to use an analysis tool such as M...
- Thu Nov 19, 2015 2:20 pm
- Forum: OptiTrack Data Streaming
- Topic: Problem with the Matlab Sample and Data Streaming
- Replies: 4
- Views: 8106
Re: Problem with the Matlab Sample and Data Streaming
Hello Ali_Ko, Thank you for reaching out to us regarding your questions. Could you let us know which sample you are using? We provide two. There are some things you might look into while troubleshooting this. Have you set the correct client and server addresses? You would need to do this manually. T...
- Wed Nov 11, 2015 1:08 pm
- Forum: Motive
- Topic: Motive 1.9.0 Beta 1 is now available
- Replies: 10
- Views: 9690
Re: Motive 1.9.0 Beta 1 is now available
Hi marianomena, Thank you for providing your feedback. It looks like this has to do with the namespace changes that were made in the C3D exporter. The next 1.9 beta should contain an additional option, when exporting C3D, that allows you to set the Marker Name Separator to "_". This will a...