Hi!
Been happily using my TIR for some time, launched today and got this:-
NATURALPOINT caused an invalid page fault in
module MFC70.DLL at 0177:7c14a0db.
Registers:
EAX=7c14a0d7 CS=0177 EIP=7c14a0db EFLGS=00210212
EBX=00000000 SS=017f ESP=0218fbec EBP=0218fc00
ECX=007b37e0 DS=017f ESI=007b37e0 FS=188f
EDX=8204e4ec ES=017f EDI=7c001156 GS=7b0e
Bytes at CS:EIP:
83 3e 00 57 0f 84 ac 00 00 00 ff 36 8b 0d 58 95
Stack dump:
0043d188 007b37e0 0218fc18 7c1f5ef8 ffffffff 0218fc24 7c14a0b5 7c15fc9e 7c160607 0043d188 0043d188 0218fc3c 7c1fa4c0 00000000 0218fc48 7c16f1cf
Un-Installed and Re-Installed Software but same!
Any suggestions?
Problem Launching TIR1
-
- Posts: 4
- Joined: Mon May 23, 2005 5:00 am
- Location: Exeter UK
Re: Problem Launching TIR1
Grecian, when you re-installed, did you plug the TIR into the same USB port?
If so try plugging it into a different port, that way all new addresses are set up as each port has it's own address.
If so try plugging it into a different port, that way all new addresses are set up as each port has it's own address.
-
- Posts: 4
- Joined: Mon May 23, 2005 5:00 am
- Location: Exeter UK
Re: Problem Launching TIR1
Thanks for suggestion , re-installed and plugged into alternate USB port, unfortunately still get the same error message
Re: Problem Launching TIR1
Grecian,
What version software do you have installed for your TrackIR?
If you launch the software without your TrackIR connected does the system still display this error?
What version software do you have installed for your TrackIR?
If you launch the software without your TrackIR connected does the system still display this error?
-
- Posts: 4
- Joined: Mon May 23, 2005 5:00 am
- Location: Exeter UK
Re: Problem Launching TIR1
Version = 3.13
Yes same error appears when I launch without TIR connected.
I'm no boffin but I looked in the Registery under:-
HKEY_CURRENT_USER\Software\NaturalPoint\NaturalPoint.
There are two folder there:-
1) NPClient Location in here:-
a) {Default} {value not set}
b) Path "C:\PROGRAMFILES\NATURALPOINT\TRACKIR\"
2) V3.13 GX in here:-
a) {Default} {value not set}
There are no other entries in 2) is this correct?
[ May 26, 2005, 06:34 PM: Message edited by: Grecian ]
Yes same error appears when I launch without TIR connected.
I'm no boffin but I looked in the Registery under:-
HKEY_CURRENT_USER\Software\NaturalPoint\NaturalPoint.
There are two folder there:-
1) NPClient Location in here:-
a) {Default} {value not set}
b) Path "C:\PROGRAMFILES\NATURALPOINT\TRACKIR\"
2) V3.13 GX in here:-
a) {Default} {value not set}
There are no other entries in 2) is this correct?
[ May 26, 2005, 06:34 PM: Message edited by: Grecian ]
-
- Posts: 4
- Joined: Mon May 23, 2005 5:00 am
- Location: Exeter UK
Re: Problem Launching TIR1
Ok, sorted , not sure what I did
I was trying out some new anti-virus software, which i since un-installed, and re-installed TrackIR ok after this, could this have caused my problem
[ June 01, 2005, 04:32 PM: Message edited by: Grecian ]
I was trying out some new anti-virus software, which i since un-installed, and re-installed TrackIR ok after this, could this have caused my problem
[ June 01, 2005, 04:32 PM: Message edited by: Grecian ]