Page 1 of 1

wand size confirmation ( 3 markers ) . preset?

Posted: Mon Mar 26, 2012 12:03 am
by lalamax3d
we (creative village) have got callibration wand (3 pts).
i attempted to measure this, my readinds
length: 680 mm app.
width: 260 mm ( distance between 3 markers )
width half: 130 mm.

1- should i use these while calibrating or should i pick preset of 500 mm wand
2- should i use width of 260 mm in 'center-distance' parameter or half of this ( 130 mm ).
thanks in advance..
regards, lala

Re: wand size confirmation ( 3 markers ) . preset?

Posted: Mon Mar 26, 2012 11:48 am
by NaturalPoint - Mike
Is this a custom calibration wand?

In general, the measurements should be center of marker to center of marker. Also, the center marker should be offset from the center a bit, so if your length is 260mm, 130mm is not a great place to put the marker, 80-95mm would be ideal. Always enter the shorter of the offset distances in the custom wand panel.

Re: wand size confirmation ( 3 markers ) . preset?

Posted: Tue Mar 27, 2012 4:47 am
by lalamax3d
thanks, this will help for sure.

Re: wand size confirmation ( 3 markers ) . preset?

Posted: Wed Mar 28, 2012 4:12 pm
by NaturalPoint - Mike
Has it worked out for you?

Re: wand size confirmation ( 3 markers ) . preset?

Posted: Mon Apr 16, 2012 4:05 am
by lalamax3d
ok, i typed, 680mm in length and 90mm in centerdistance parameter. it didn't worked out well.
then in same setup, i put 500 mm wand preset and it worked (not ideal)>>details
i kept wanding for 2 to 3 minutes. it shows highquality with poor accuracy, each camera was poor. but ground detection works good. plus i can see all cameras in viewport pretty reasonable.
currently overall volume is 20 sq feet area.

i have my fears to test capture session at this point. i am thinking...

in previous two sessions, we did
first was smaller area and 500 preset worked well
in second session (next day) i attempted to increase volume a lot. more than 30 sq feet area. i tried all values and nothing worked. it never worked. thats why i started this thread. please suggest what possibilites are going to improve accuracy.?
thanks, lala

Re: wand size confirmation ( 3 markers ) . preset?

Posted: Tue Apr 17, 2012 10:02 am
by NaturalPoint - Mike
Length is the distance between the centers of the two outside markers, which looks like it's 230mm according to the original post.

Handle length is not needed.

Re: wand size confirmation ( 3 markers ) . preset?

Posted: Mon Apr 23, 2012 6:30 am
by lalamax3d
wow. everything same, just difference. so someone else can get benefit from ..
its an image image 1 : 500mm : default wand settings
its another image image 2 : 680-230mm custom settings as per my readings


so i am going for default results

Re: wand size confirmation ( 3 markers ) . preset?

Posted: Mon Apr 23, 2012 2:34 pm
by NaturalPoint - Mike
Keep in mind if Arena thinks the wand is a different size than it actually is, you'll get volume scaling issues.

Re: wand size confirmation ( 3 markers ) . preset?

Posted: Tue Jun 05, 2012 3:44 pm
by farstar
I have your factory 3 point wand what should i set me wand size to?

Re: wand size confirmation ( 3 markers ) . preset?

Posted: Tue Jun 05, 2012 4:29 pm
by NaturalPoint - Mike
There are three different factory versions. The standalone single wand was 400mm from end to end, the optiwand kit with multiple crossbars is either 500mm or 250mm end to end. The best way to know for sure is to measure from the center of one of the outside markers to the center of the other outside marker.